Tag Archives: optimization

Snagless RJ45 connectors – How To Make Network Cables Snagless

Patch Panel

Snagless RJ45 Connectors – the Odd Request

Snagless RJ45 connectors are that odd request that my department makes from time to time. Why do you need RJ45 connectors anyway, it’s the invariable answer from supervisors, and the typical reminder: “You have all sorts of patchcords, all dimensions…” Well, first of all, we sysadmins never have all the patchcords dimensions available. The IT racks should be something that should be kept as tidy as possible, and one way is to have custom length of the patchcords.

Depending on your infrastructure, you might want or might not want to use handmade patchcords in your racks; however, in many cases this is totally acceptable. You can probably make a Cat 5 patchcord, but you won’t be able to make a Cat 6 one. In other words your hand made patchcords will be able to run at Gigabit speeds, but not at 10 Gigabit speeds, even with the proper connectors and cables. Having said that, most of the equipment in a business server room is connected into a Gigabit switch or at lower speeds, so this would not be a problem.

Custom Patchcords – Always Broken Lokcing Tabs

The major problem with all the handmade Ethernet patchcords and cables is that the locking tab is breaking. I probably don’t have to explain why broken tabs are bad; they will not be secured into the equipment’s jack, resulting in intermittent data loss, or even disconnection.

There are two reasons for the locking tabs breaking so often. Firstly, the little locking tab is very fragile, and we can’t change that, it is fragile to keep the costs down. The other reason is the design, the locking tab sticks out, and it is very easy to get snagged and broken off. All store-bought cables come with a snagless boot; it’s the standard these days. All the cables with broken locking tabs don’t have the boots, because they are terminated in place, by either a datacom tech, or an admin.

These plugs from Panduit are the best snagless RJ45 connectors.

The connectors are meant for patch cords, and they are rated as providing Category 5e performance.

The patented tangle-free plug latch prevents snags, hence breaking.

They are easy release, unlike some snagless boots, and they save time on frequent moves, adds, and changes.

The design facilitates easy insertion and termination of wires

What Is the Solution for Broken RJ45 Connectors

One of the solutions to fix the snagging network cables is to install a "snagless" boot over the cable, before crimping the connector. After crimping, just push the boot over the connector and the boot will protect the little tab.

My preferred way to fix this is to use snagless RJ45 connectors, and a boot. This ensures the plug will not break ever, unless you purposely do it. You can also use just the snagless connectors, they are very good, and I do it very often, but if I have both the snagless connectors and the snagless boots, I will use both for optimization. The snagless plugs are slightly more expensive than the regular ones, but when you draw the line, and consider the troubleshooting needed on the long term, and the fact that sooner or later those RJ45 connectors will break and will need to be replaced, the additional cost is worth paying.

Like I already mentioned before, with the low prices for commercial made patchcords, and the quality ensured by a machine made ethernet cable, there is no need to make your own, it's just not practical.

This cables are made in a commercial facility, they are tested, and they come in a variety of lengths, just choose the one that is right for you. You can even get  to choose the color, so you can color code your patch panel connections, so everything looks tidy, and easy to follow.

Troubleshoot a Slow Network – Slow Server

Slow Server

How do we know the server is slow and the problem is not elsewhere?
Make a file transfer between any two other computers on the network. Compare the measurements with the server’s transfer rates.
What are the reasons for a slow server?
There are many reasons for a slow server. The server is many times the bottle-neck of a network. Here are a few reasons for a slow server:
An average, or below average network card, (you need good quality network cards for a server).
Server Network Card Underutilized. Connect your server on the backbone or on 1GB switch ports to make use of the high speed network card. You probably want to limit all your clients to transfer at 100Mb so that there is no traffic discrimination. If your server and switches support higher transfer rates, (10GB ports), make sure you make use of it.
Slow disks. Poor hardware is many times the main reason. Improper configuration, such as choosing the wrong RAID type, or not using write caching can be another reason.
Too many clients on a server. If too many clients make requests to the same single server this could overload the server and it will perceived as a slow network by the users. Measure your server’s performance on load using the performance logs and alerts and the system monitor in Windows. Usually the performance is changing over the course of a day based on the number of users who access the server at the same time. Sometimes adding another network card would be sufficient. Enabling cache writing on the SCSI card can help a lot, (make sure you install a cache battery), adding a new SCSI card and additional disks to offload the existing ones could be of help. Sometimes adding another CPU can make a difference, (if you have free CPU slots). Memory is very often the most used method of upgrading, but most of the times it is not the needed solution. Use the performance logs and alerts and the system monitor and compare with the recommended thresholds to determine what your bottleneck is.
Slow server response, (packet sniffer to determine the handshake time), Adjust the server’s configuration to optimize the handshaking time; (this is a fairly advanced optimization task).

This article is part of a five posts series regarding Network Troubleshooting.

What Are the Best Ways to Increase Website Link Popularity?

What is Link Popularity

Link popularity is the total number of web pages and websites that link to a web page. Link popularity is used by search engines to compare sites and rank them in search results. Search results are important for Internet Businesses because a better rank brings more visitors to your website.

What is the best method to Increase Website’s Popularity?

Generally, you will get higher rankings, consequently more traffic, if you use more than one way. You need to use every method, (article marketing, Web 2.0 marketing, social bookmarking, RSS submission, press releases, video marketing, social networking, and forum discussions). Relying on only one strategy could be the difference from good to great.

[ad#Adsense Text 468 wide]

What is the Best Linking Method?

One of the most effective linking methods is Article Marketing. The disadvantage of Article Marketing is that it is time-consuming. For any two to four links that you get, depending on the Directory’s terms, you need to write a new article with original content.
Submit your article to a good Article Directory.
Make sure you submit unique articles and do not use duplicate content even if it’s yours. Google announced that they would hunt down duplicate articles as part of their campaign of search results improvement and spam fighting. If you write good articles, you will get a lot of traffic from these articles.

SEO Optimizations

Anchor Text is a key factor in search optimization. When you publish a backlink, you have to use a relevant anchor text. You will have no benefit from irrelevant text anchors, or little benefit from poorly chosen keywords. A common mistake is to insist on the website’s name or domain name. As an Example if you owned BlaBla Directory and your domain is blabladirectory.com, there is no point to promote your site using the anchor text BlaBla Directory, because there is a small chance that someone else will rank better than you for that keyword. Promote instead Directory or List Your Site or any other search terms that make sense.
Try to post and comment on sites that do not use "no-follow" tag. Do not avoid no-follow links, are still of some value and make sense to search engines when they calculate your site’s reputation.
Relevancy is another important factor of your links. If the context of the link is not related to your website then the link values less.

Note that not all the link popularity techniques marketed as SEO services are approved by Search Engines. These are against the Terms of Service and your website could be banned for manipulating search engine results.
When considering using the services of an Internet Marketing company, ensure you fully understand all of the proposed campaign’s details.